NEC Electronics Sets New Bar for ARM Processor Core Performance

700 MHz ARM11 MPCore Processor is Industry's Highest Performing; 130 nm ARM926EJ-S Processor is Industry's Fastest

KAWASAKI, Japan, SANTA CLARA, Calif. and DUESSELDORF, Germany, Aug. 28 /PRNewswire/ -- Raising the bar for ARM(R) processor performance, NEC Electronics Corporation today unveiled two 32-bit ARM processor cores that can be used with NEC Electronics' proven system-on-chip (SoC) design methodology to develop high-speed solutions for networking, wireless, digital consumer, imaging, storage, automotive and industrial applications. NEC Electronics' 90-nanometer (nm), 700 MHz (931 MHz under nominal process conditions) dual-core implementation of the ARM11(TM) MPCore(TM) multicore processor is the highest-performing ARM processor core on the market, while the NEC Electronics-implemented ARM926EJ-S(TM) processor core is the industry's fastest at 130 nm, clocking in at 400 MHz (532 MHz under nominal process conditions).

"Capable of executing more than 2200 Dhrystone MIPS under nominal conditions, NEC Electronics' dual-core implementation of the ARM11 MPCore is the highest-performance implementation available today. The processor is well suited to high-speed consumer, enterprise and networking applications that are typically served by much more expensive processors," said John Goodacre, Program Manager, Multiprocessing, ARM. "For value markets, the NEC Electronics implementation of the 130 nm ARM926EJ-S processor is the industry's fastest in its class."

Fast Processors Meet Varied Market Requirements

Based on the ARM11 microarchitecture, the 700 MHz (worst-case process, temperature and voltage) ARM11 MPCore is implemented using NEC Electronics' 90 nm process technology and delivers ultra-high performance through multiprocessing at a lower frequency than comparable single-processor solutions, which can result in significant cost savings for system designers. Full compatibility with existing electronic design automation (EDA) tools and flows can simplify otherwise complex multiprocessor design development and reduce time to market and design costs.

NEC Electronics' new implementation of the ARM926EJ-S processor achieves a speed of 400 MHz (worst-case process, temperature and voltage) and is available for implementation with NEC Electronics' 130 nm ASIC technology. The high-performance operation at this node can reduce design costs and mitigate the risks associated with moving to smaller geometries.

This digital signal processor (DSP)-enhanced 32-bit RISC processor is well suited to applications requiring a mix of DSP and microcontroller (MCU) functionality in the digital consumer, imaging, storage, automotive and industrial markets. In addition to signal-processing extensions to enhance 16-bit fixed-point performance using a single-cycle 32 x 16 multiply-accumulate (MAC) unit, the ARM926EJ-S processor incorporates ARM's Jazelle(R) technology that enables direct execution of Java byte codes in hardware and a 16-bit ARM Thumb(R) instruction set that shrinks code size and, consequently, reduces system cost.

"Through its strategic relationship with ARM, NEC Electronics is able to offer a wide range of processor cores based on an architecture that combines high performance with low power consumption and low system cost," said Kazu Yamada, vice president and general manager, Custom SoC Solutions strategic business unit, NEC Electronics America, Inc. "The 700 MHz and 400 MHz cores announced today demonstrate NEC Electronics' ability to combine design expertise with leading-edge process technologies to develop ARM-based processor solutions that meet exacting system requirements."


The silicon-proven 400 MHz ARM926EJ-S processor is currently available in NEC Electronics' CB-130M IP library. The 700 MHz ARM11 MPCore multicore processor is scheduled to be available for SoC integration before the end of 2007 in the CB-90M IP library. Both processors are available for either cell-based IC (CB-IC) or customer-owned tooling (COT) applications. More information can be found at . (Availability is subject to change.)

About NEC Electronics

NEC Electronics Corporation specializes in semiconductor products encompassing advanced technology solutions for the high-end computing and broadband networking markets, system solutions for the mobile handset, PC peripherals, automotive and digital consumer markets, and platform solutions for a wide range of customer applications. NEC Electronics Corporation has 25 subsidiaries worldwide including NEC Electronics America, Inc. ( and NEC Electronics (Europe) GmbH ( For additional information about NEC Electronics worldwide, visit

ARM, Jazelle and Thumb are registered trademarks of ARM Limited. ARM11, ARM926EJ-S and MPCore are trademarks of ARM Limited. "ARM" is used to represent ARM Holdings plc; its operating company ARM Limited; and the regional subsidiaries ARM, Inc.; ARM KK; ARM Korea Ltd.; ARM Taiwan Limited; ARM France SAS; ARM Consulting (Shanghai) Co. Ltd.; ARM Belgium N.V.; AXYS Design Automation Inc.; ARM Germany GmbH; ARM Embedded Technologies Pvt. Ltd.; and ARM Norway, AS. NEC Electronics is either a registered trademark or trademark of NEC Electronics Corporation in the United States and/or other countries. All other registered trademarks or trademarks are property of their respective owners.

Web site:

Review Article Be the first to review this article

ClioSoft at DAC

Featured Video
Senior Electrical Engineer for Allen & Shariff Corporation at Pittsburgh, Pennsylvania
Upcoming Events
Symposium on Counterfeit Parts and Materials 2018 at College Park Marriott Hotel & Conference Center MD - Jun 26 - 28, 2018
Concar Expo 2018 at Convention Hall II Sonnenallee 225 Berlin Germany - Jun 27 - 28, 2018
Nanotech 2019 at Tokyo Big Sight East Halls 4-6 & Conference Tower Tokyo Japan - Jun 30 - 1, 2018
INMMiC 2018 at university campus of Brive La Gaillarde France - Jul 5 - 6, 2018
ClioSoft at DAC

Internet Business Systems © 2018 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise