IC Insights Bulletin: Companies Maximize 300mm, 200mm Wafers; Slow Progress on 450mm

 
Companies Maximize 300mm, 200mm Wafers; Slow Progress on 450mm
Installed capacity, number of 300mm wafer fabs increasing through 2019.
 
Larger wafer diameters provide more chips per wafer at a modest increase in material and process costs, resulting in reduced chip costs.  Historically, transitions to larger diameter wafers have provided cost reductions greater than 20% per unit area.  However, enormous financial and technology hurdles continue to plague the development of, and the transition to, 450mm wafers.  As a result, the transition to larger diameter wafer has slowed dramatically and companies are maximizing their efficiency using 300mm and 200mm wafers.  IC Insights’ Global Wafer Capacity 2015-2019 report shows that worldwide capacity by wafer size was dominated by 300mm wafers in 2014 and is forecast to continue increasing through 2019 (Figure 1).

Figure 1
 
Efforts to develop 450mm wafer technology continue to make some progress, but the pace of development slowed significantly in 2014.  Now, by most accounts, volume production using 450mm wafers is not expected before 2020, although pilot production could start a year or two before.  IC Insights shows 450mm wafers accounting for a very slim share of installed capacity in 2019.

For the most part, 300mm fabs are, and will continue to be, limited to production of high-volume, commodity-type devices like DRAMs and flash memories; image sensors and power management devices; and complex logic and microcomponent ICs with large die sizes; and by foundries, which can fill a 300mm fab by combining wafer orders from many sources.

At the end of 2014, there were 87 production-class IC fabs utilizing 300mm wafers (Figure 2).  There are several 300mm R&D IC fabs and a few high-volume 300mm fabs around the world that make “non-IC” products such as image sensors and discretes, but these are not included in the count shown in the chart.

Figure 2
 
Only once—in 2013—has the number of 300mm wafer fabs declined.  That year, three large fabs operated by ProMOS and Powerchip closed and setbacks delayed the opening of several new 300mm fabs until 2014. By the end of 2019, there are expected to be 23 more 300mm wafer fabs in operation than there were at the close of 2014.  The number of 300mm fabs will likely peak between 115-120, which assumes 450mm fabs will enter volume production in the future.  For comparison, the greatest number of volume-production 200mm wafer fabs in operation was 210 (the number declined to 154 fabs at the end of 2014).

The list of companies with the most 300mm wafer capacity includes memory suppliers Samsung, Micron, SK Hynix, and Toshiba/SanDisk; the industry’s biggest IC manufacturer and dominant MPU supplier Intel; and the world’s two largest pure-play foundries TSMC and GlobalFoundries.  These companies offer the types of ICs that benefit most from using the largest wafer size available to best amortize the manufacturing cost per die.

The number of fabs running 200mm wafers will continue to be profitable for many more years and be used to fabricate numerous types of ICs including specialty memories, display drivers, microcontrollers, analog products, and MEMS-based devices. Devices like these are practical to make in fully depreciated 200mm fabs that were used to produce devices now made on 300mm wafers.  TSMC, TI, and UMC remain the three companies with the greatest amount of 200mm wafer fab capacity.
 
Report Details:  Global Wafer Capacity 2015-2019

Additional details and a forecast of the IC industry’s wafer fab capacity through 2019 are provided in IC Insights’ Global Wafer Capacity 2015-2019—Detailed Analysis and Forecast of the IC Industry’s Wafer Fab Capacity report.  The Global Wafer Capacity report assesses the IC industry’s capacity by wafer size, minimum process geometry, technology type, geographic region, and by device type through 2019. The report also includes detailed profiles of the companies most likely to build 450mm wafer fabs and gives detailed specifications on existing wafer fab facilities.  Coupled with IC Insights’ Strategic Reviews database of more than 185 company profiles, the two reports provide a tremendous resource for researching, evaluating, and comparing wafer fab facilities and industry capacity. Global Wafer Capacity 2015-2019 is priced at $4,290 for an individual user password.  A multi-user worldwide corporate license is available for $6,990.
 
To review additional information about IC Insights’ new and existing market research reports and services please visit our website: www.icinsights.com.
 
More Information Contact
For more information regarding this Research Bulletin, please contact Bill McClean, President, at IC Insights. Phone: +1-480-348-1133, email: Email Contact

PDF Version of This Bulletin
A PDF version of this Research Bulletin can be downloaded from our website at http://www.icinsights.com/news/bulletins/



Review Article Be the first to review this article
CST Webinar Series



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy