At-speed in-system programming of flash memory enhanced with ScanWorks FPGA-Controlled Test and IJTAG

New capability takes advantage of an IJTAG network with programming engines embedded in an onboard FPGA

August 25, 2015 -- Programming memory in-system, or after the devices have been soldered to a circuit board, is the most efficient method, but the challenge for design and manufacturing engineers has always been the slow speeds of the process. Now, enhancements to ASSET® InterTech’s ScanWorks® platform for embedded instruments can speed up in-system programming by a factor of 1,000, reducing programming times from 10 or more minutes to one or two seconds. ASSET ( is a leading supplier of software and hardware debug, validation and test tools.

The ScanWorks platform’s FPGA-Controlled Test (FCT) tool inserts a board tester with multiple instruments into a functional FPGA. The tester can then be used by design and manufacturing engineers. One of the new enhancements to ScanWorks FCT is the availability of high-speed programming engines which can load memories connected to the FPGA in a fraction of the time previously possible. ScanWorks FCT can program all sorts of flash memories, including NOR and NAND flash, as well as memory connected to the FPGA by the I2C and SPI buses.

“Most design and production engineers will say that the preferred way to program memory is in-system. Prototype boards are often produced before the system’s functional firmware is complete. Without in-system programming, a change in the software would mean de-soldering memory, programming it again and then re-soldering it to the board. Often, the devices or the board are damaged,” said Kent Zetterberg, ASSET’s product manager for ScanWorks FCT. “And in production, the software for some boards isn’t loaded until a customer orders a certain configuration of the system. Programming the memory in-system and at-speed is a tremendous benefit in both of these instances.”

The ScanWorks FCT high-speed programming engines take advantage of the IEEE 1149.1 JTAG port on FPGAs without some of its drawbacks, such as slow programming speeds caused by long scan chains. ScanWorks FCT and its programming engines are based on the IEEE 1687 Internal JTAG (IJTAG) standard which embeds a network of instruments in chips, including FPGAs, systems-on-a-chip (SoC) and others. This IJTAG network of embedded instruments can act as a shortcut into onboard memory devices to perform in-system flash programming much faster.

ASSET has posted a number of eBooks in its eResources Center on the topic of fast flash programming. One such eBook is titled “ Faster Flash Programming via FPGA and IJTAG.”

About ASSET InterTech

ASSET InterTech ( is a leading supplier of tools to debug, validate and test software and hardware. The company’s SourcePoint™ software debug and trace platform and ScanWorks® platform for embedded instruments work in tandem to give engineers real insight from code to silicon. SourcePoint is a best-in-class, powerful debugger that includes advanced trace tools to gather data from code and quickly debug complex embedded software systems. ScanWorks controls instruments embedded in chips to test and validate chips and circuit boards. Together they empower engineers with tools and technology for the entire life-cycle of a system, beginning with software and hardware development, on to design validation, through software/hardware integration, and eventually testing the product in manufacturing and field service. ASSET InterTech is located at 2201 North Central Expressway, Suite 105, Richardson, TX 75080.

Follow us on:






Read the complete story ...

Review Article Be the first to review this article

Featured Video
Peggy AycinenaWhat Would Joe Do?
by Peggy Aycinena
Simon Davidmann: A re-energized Imperas Tutorial at DAC
More Editorial  
LVS for PDK Design Engineer SILICON VALLEY for EDA Careers at San Jose, CA
DDR 3-4-5 Developer with VIP for EDA Careers at San Jose, CA
Senior Front-End RTL Design AE for EDA Careers at San Jose, CA
Upcoming Events
11th International Conference on Verification and Evaluation of Computer and Communication Systems at 1455 DeMaisonneuve W. EV05.139 Montreal Quebec Canada - Aug 24 - 25, 2017
DVCon India 2017, Sept 14 - 15, 2017 at The Leela Palace Bengalore India - Sep 14 - 15, 2017
SMTA International 2017 at Rosemont IL - Sep 17 - 21, 2017
S2C: FPGA Base prototyping- Download white paper

Internet Business Systems © 2017 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy