DCD’s D16950 – ask for more from UART

DCD, celebrating its 15thanniversary, has released the D16950, which is an IP Core of a Universal Asynchronous Receiver/Transmitter (UART), functionally compatible to the OX16C950. It allows serial transmission in two modes: UART and FIFO. In the FIFO mode, internal FIFOs are activated, allowing 128 bytes (plus 3 bits of error data per byte in the RCVR FIFO) to be stored in both receive and transmit modes.

Bytom, Poland. 3rd of June 2014 -- DCD’s UART IP Core performs a serial-to-parallel conversion on data characters received from a peripheral device or a MODEM. And for those who need more, the D16950 enables also parallel-to-serial conversion on data characters received from the CPU. The processor can read a complete status of the UART at any time during the functional operation. Reportedstatus information includes the type and condition of transfer operations being performed by the UART, as well as any error conditions (parity, overrun, framing or break interrupt). - The D16950 includes a programmable baud rate generator, which is capable to divide the timing reference clock input by divisors of 1 to (216-1) and produce a n × clock for driving the internal transmitter logic – explains Jacek Hanke, DCD’s CEO.  Provisions are also included to use this n × clock to drive the receiver logic.

The D16950 UART IP Core is equipped with a complete MODEM-control capability and a processor-interrupt system. - Interrupts can be programmed in accordance to your requirements, minimizing computing required to handle the communications link – adds Hanke. The D16950 core includes all other UARTs (16450, 16550, 16650 and 16750) features and additional functions. Saying this, one can mention the ICR registers, which give additional capabilities of UART work configuration. The data transmission may be synchronized by an external clock connected to the RI (for receiver and transmitter) or the DSR (only for receiver) pin. The NMR register enables a 9-bit mode transmission, with or without special character. Writing and reading from/to FIFO may be controlled by trigger level registers, with any value set from 1 to 127.

DCD’s IP Core implements also autoflow control feature, which can significantly reduce software overload and automatically increase the system efficiency, by controlling serial data flow through the RTS output and the CTS input signals.

The D16950 is perfect for applications, where the UART core and the microcontroller are clocked by the same clock signal and are implemented inside the same ASIC or FPGA chip. Nevertheless, it's also a proprietary solution for a standalone implementation, where several UARTs are required to be implemented inside a single chip and driven by some off-chip devices. Thanks to a universal interface, the D16950 core implementation and verification are very simple, just by eliminating a number of clock trees in the complete system.

DCD’s IP Core includes fully automated testbench with complete set of tests, allowing easy package validation at each stage of SoC design flow. The D16950 is also a technology independent design, that can be implemented in a variety of process technologies.

More information: http://dcd.pl/ipcore/130/d16950/

Key Features:

  • Software compatible with 16450, 16550,16650,16750 and 16950 UARTs
  • Configuration capability
  • Separate configurable BAUD clock line
  • Majority Voting Logic
  • Two modes of operation: UART mode and FIFO mode
  • In the FIFO mode transmitter and receiver are each buffered with 128 byte FIFO to reduce the number of interrupts presented to the CPU
  • In UART mode receiver and transmitter are double buffered to eliminate the need for precise synchronization between the CPU and serial data
  • Configurable FIFO size up to 512 levels
  • Adds or deletes standard asynchronous communication bits (start, stop and parity) to or from the serial data
  • Independently controlled transmit, receive, line status and data set interrupts
  • False start bit detection
  • 16 bit programmable baud generator
  • Independent receiver clock input
  • MODEM control functions (CTS, RTS, DSR, DTR, RI, DCD)
  • Programmable Hardware Flow Control through RTS and CTS
  • Programmable Flow Control using DTR and DSR
  • Programmable in-band Flow Control using XON/XOFF
  • Programmable special characters detection
  • Trigger levels for TX and RX FIFO
  • Interrupts and automatic in-band and out-off-band flow control
  • Fully programmable serial-interface characteristics:
  • 5-, 6-, 7-, 8- or 9-bit characters
  • Even, odd, or no-parity bit generation and detection
  • 1-, 1.5-, or 2-stop bit generation
  • Internal baud generator
  • Detection of bad data in receiver FIFO
  • Clock prescaler from 1 to 31,875
  • Enhanced isochronous clock option
  • 9- bit data mode
  • Software reset
  • Complete status reporting capabilities
  • Line break generation and detection. Internal diagnostic capabilities:
  • Loop-back controls for communications link fault isolation
  • Break, parity, overrun, framing error simulation
  • Full prioritized interrupt system controls
  • Available system interface wrappers:
  • AMBA - APB Bus
  • Altera Avalon Bus
  • Xilinx OPB Bus
  • Fully synthesizable
  • Static synchronous design and no internal tri-states

Information about Digital Core Design:

In 2014 Digital Core Design celebrates its 15th Anniversary. The company founded in 1999, since the beginning stands in the forefront of the IP Core market. High specialization and profound customer service enabled to introduce more than 70 different architectures. Among them is the world’s fastest 8051 IP Core, the DQ80251, which is more than 66 times faster than the standard solution. As an effect, over 300 hundred licensees have been sold to more than 500 companies worldwide. Among them are the biggest enterprises like e.g. Sony, Siemens, General Electric and Toyota. But a lot of DCD’s customers are small businesses, R&D laboratories or front/back end offices, which require exact solution tailored to their project needs. Rough estimations say that more than 250 000 000 devices around the globe have been based on Digital Core Design’s IP Cores.



Contact:

Tomeq Cwienk,
tel: + 48 32 282 82 66 ext.25,
skype: tomasz.cwienk,
mail to: Email Contact




Review Article Be the first to review this article
CST Webinar Series

EMA:

Featured Video
Editorial
Peggy AycinenaWhat Would Joe Do?
by Peggy Aycinena
Retail Therapy: Jump starting Black Friday
Peggy AycinenaIP Showcase
by Peggy Aycinena
REUSE 2016: Addressing the Four Freedoms
More Editorial  
Jobs
FAE FIELD APPLICATIONS SAN DIEGO for EDA Careers at San Diego, CA
Development Engineer-WEB SKILLS +++ for EDA Careers at North Valley, CA
AE-APPS SUPPORT/TMM for EDA Careers at San Jose-SOCAL-AZ, CA
ACCOUNT MANAGER MUNICH GERMANY EU for EDA Careers at MUNICH, Germany
Manager, Field Applications Engineering for Real Intent at Sunnyvale, CA
Upcoming Events
Zuken Innovation World 2017, April 24 - 26, 2017, Hilton Head Marriott Resort & Spa in Hilton Head Island, SC at Hilton Head Marriott Resort & Spa Hilton Head Island NC - Apr 24 - 26, 2017
CST Webinar Series



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy