Power, accuracy and noise aspects in CMOS mixed-signal design

Title: Power, accuracy and noise aspects in CMOS mixed-signal design
Author: Sanduleanu, Mihai Adrian Tiberiu
ISBN: 90-3651265-4
©1999, Mihai A.T. Sanduleanu

Table of Contents

Selected Symbols and Abbreviations
 
Chapter 1   Introduction
  1.1. Motivation
  1.2. Problem definition
  1.3. Scope and outline
  References
 
Chapter 2 Power considerations in sub-micron digital CMOS
  2.1. Introduction
  2.2. Fundamental limits
  2.3. From fundamental limits to practical limits of power. An architecture level approach
  2.4. S/N ratio and power in fixed point applications
  2.5. Adders and computational power
  2.6. Ways to low-power in digital
  2.7. Example of a digital video filter
  2.8. Conclusions
  2.8. References
 
Chapter 3 Power considerations in sub-micron analog CMOS
  3.1. Introduction
  3.2. Process tuning towards digital needs. Consequences on analog
  3.3. Fundamental limits
  3.4. From fundamental limits to practical limits of power. Noise related power
  3.5. From fundamental limits to practical limits of power. Mismatch related power
  3.6. Power estimations in continuous time filters
  3.7. Conclusions
  References
 
Chapter 4 Gm-C integrators for low-power and low voltage applications. A gaussian polyphase filter for mobile transceivers in 0.35mm CMOS
  4.1. Introduction
  4.2. Large swing and high linearity transconductor
  4.3. Low voltage current Gm-C integrator with high power efficiency
  4.4. Low-power luminance video filter. Noise driven power
  4.5. Low-power, gaussian, polyphase filter for mobile transceivers. Matching driven power
  4.6. Conclusions
  References
 
Chapter 5 Chopping: a technique for noise and offset reduction
  5.1. Introduction
  5.2. Ways to reduce offset and 1/f noise
  5.3. Chopping seen as a modulation technique
  5.4. Noise modulation
  5.5. Chopped amplifiers and offset reduction
  5.6. Low-power low-voltage chopped transconductance amplifier for noise and offset reduction
  5.7. A low-power bandgap voltage reference
  5.8. Conclusions
  References
 
Chapter 6 Low-noise, low residual offset, chopped amplifiers for high-end application
  6.1. Introduction
  6.2. Low-pass filtering in a digital audio system. Application specific constraints
  6.3. The gain stage
  6.4. A low noise, low residual offset, chopped amplifier in 0.8mm CMOS
  6.5. A low noise, low residual offset, chopped amplifier in 0.5mm CMOS
  6.6. Conclusions
  References
 
Chapter 7 A 16-bit D/A interface with Sinc approximated semidigital reconstruction filter
  7.1. Introduction
  7.2. Bitstream D/A conversion system with time-discrete filtering
  7.3. S-D modulators and noise shaping
  7.4. Semidigital FIR filter principles
  7.5. Semidigital FIR filter design
  7.6. Noise properties of the D/A interface
  7.7. Realisation
  7.8. Experimental results
  7.9. Interpolative D/A converter with Sinc approximation in the time domain
  7.10. Conclusions
  References
 
Chapter 8 Conclusions
  8.1. Summary
  8.2. Conclusions
  8.3. Original contributions
  8.4. Recommendations for further research
 
Appendix 1
 
Appendix 2
 
Appendix 3
 

ALDEC:

Featured Video
Editorial
Peggy AycinenaWhat Would Joe Do?
by Peggy Aycinena
Reverie: All That Glitters is not Past
More Editorial  
Jobs
FAE FIELD APPLICATIONS SAN DIEGO for EDA Careers at San Diego, CA
Development Engineer-WEB SKILLS +++ for EDA Careers at North Valley, CA
Technical Marketing Manager Valley for EDA Careers at San Jose, CA
Senior Physical Design Engineer for Ambiq Micro at Austin, TX
Technical Support Engineer for EDA Careers at Freemont, CA
Digital and FPGA Hardware Designer for Giga-tronics Incorporated at San Ramon, CA
Upcoming Events
European 3D Summit 2017 at 3, parvis Louis Néel 38054 Grenoble France - Jan 23 - 25, 2017
3D Printing Electronics Conference at High Tech Campus 1, 5656 Eindhoven Eindhoven Netherlands - Jan 24, 2017
DesignCon 2017 at Santa Clara Convention Center Santa Clara CA - Jan 31 - 2, 2017
Embedded Neural Network Summit at San Jose CA - Feb 1, 2017



Internet Business Systems © 2017 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy