Logic Design for Array-Based Circuits

by Donnamaie E. White

Copyright © 1996, 2001, 2002 Donnamaie E. White


Power Considerations

Last Edit July 22, 2001

Step 10: Determine ECL Static Power PEO

The equation used by the AMCC MacroMatrix ERC software to compute ECL static power dissipation for ECL outputs is:


where XX is the current based on the termination

The 1.3V term represents the average between VOH and VOL. This is considered to be the statistical worst-case for this function

If there is more than one termination, the power for each type of termination is computed and summed to find the total PECL outputs

ECL Output Termination Current

Table 7-15 provides the ECL output termination currents used by the AMCC MacroMatrix ERC software. The currents shown are the average current (average of IOH and IOL)

AMCC automated ECL static power is computed with the 50 or 25 ohm termination under the assumption of 50% terminations active. This is because AMCC provides macros that drive 50 ohm loads and macros that drive 25 ohm loads. These assumptions may vary with the vendor.

Table 7-15 ECL Termination Current

ohm mA
25 28.0
50 14.0
100 7.0
200 3.5

* the average current (average of IOH and IOL) for termination to -2V

* When 50 ohm or 25 ohm Terminations are Not Used

Resistive loads that differ from that used by automation software will require manual computation. These loads should be identified when performing design submission to any vendor.

If other ECL output load resistances are used, the actual current value must be computed for use in the ECL static power equation. For a -2V termination, to find the average current in mA, use the following equation.

    I in mA = 0.7/( R * (10-3)) for any R

* When VT Ê -2V

For other termination voltages, an adjustment to the power dissipation computation must be made by the designer. For a termination voltage VT, to find the average current in mA, use the following equation.

    I in mA = (-1.3V - VT)/( R * (10-3)) for any R

* Darlington ECL Outputs

Darlington ECL outputs are treated as a standard ECL outputs for static power computations.

* On-Chip Series Termination

There is no IOEF output current for on-chip series termination ECL output macros. All current (power) dissipated is specified in the macro docu-mentation.

Step 11: Sum the Result - Total DC power

Sum the results of the macro and overhead current power computations with any ECL output macro static power dissipation to obtain the total worst-case DC power dissipation for the circuit:


The result is the total worst-case DC power dissipated by the circuit on the target array.


  1. Determine how current or power is specified for an array series of interest. Is it worst-case? If not, find out how the data is converted to worst-case for Commercial and for Military operating conditions.

  2. Determine how overhead current is accounted for by this array series. Is it variable? If so, determine what affects it, e.g., number of I/O by type or their placement.

  3. What other adjustments are required before a final DC power value can be obtained? If the manual is not specific, consult the vendor.

  4. AMCC Q20000 Exercise. A 100% ECL circuit has been designed using the Q20080 (8K) array. It uses the following example values:

    Macro Name: Number Used: Current: IEE mA
    FF10S 32 0.98
    FF46S 32 0.93
    GT09S 0 0.39
    GT55D 4 0.91
    GT60L 6 0.64
    GT60S 6 0.78
    GT87D 2 0.49
    IE31H 1 2.20
    IE93S 82 1.03
    IEVCC 9 0.00
    MX21S 20 0.66
    OE42S 69 8.72

    Typical current is specified for one occurrence of each macro. The power supply is nominal -5.2V. The circuit is military. Compute its DC power dissipation given the above portion of the macro occurrence table and the other tables provided in the text. [Ans.: 8.32 Watts (1994 data)]

  5. Substitute 32 OE14S macros that use 6.69 mA each for 64 of the OE42S macros and delete one of the GT87D macros. Now how much power is dissipated?

Copyright @ 2001, 2002 Donnamaie E. White, White Enterprises
For problems or questions on these pages, contact dew@Donnamaie.com

TrueCircuits: UltraPLL

Internet Business Systems © 2017 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy