Logic Design for Array-Based Circuits

by Donnamaie E. White

Copyright © 1996, 2001, 2002 Donnamaie E. White

 

External Set-Up and Hold Times

Last Edit July 22, 2001


Computing Hold Time in the Register Example

To compute the hold time of the design, the propagation delay of both paths needs to be determined while factoring in the effects of tracking.

  • The worst-case tracking occurs when tracking
  • reduces the path propagation delay of both the
  • clock path PATH1 and the clock-to-output (Tpd)
  • delay of the last flip/flop in the chain that is
  • connected to PATH1 (FF15). This includes both
  • the intrinsic and extrinsic delays.

The general equation for the example is as follows (using 10% tracking for the first macro in PATH1, and 20% tracking for the second macro):

10% 20%
WCM * [ 0.9 * Tpd D1 + 0.8 * Tpd FF15 - Tpd D2 ] > Th FF16
TRK1 TRK2

where Tpd is nominal. For the example, the driver macros (D1) are identical and placed within the same chip quadrant. For the Q5000 Series, this has been specified to mean a 10% tracking (0.9). For identical macros on the same row in the same quadrant, this reduces to 5% tracking or 0.95. TRK1 will be taken at 10%.

The second tracking factor (TRK2) applies to FF15. This accounts for unlike edges and unlike structures between D2 and FF15. It does assume that both are placed within the same quadrant.

For macros that are not identical, placed in the same quadrant on the array, tracking is defined as 20% or 0.8. TRK2 will be taken as 20%. These numbers only apply to the AMCC Q5000 Series. The timing diagram for Figure 6-5 is shown in Figure 6-7.

Minimum Library (Q5000 Series)

For the example, for a military circuit, using bipolar worst-case multipliers (AMCC Q5000 Series), the equation for the Minimum Library minimum values becomes:

0.86 * [0.9 * Tpd D1 + 0.8 * Tpd FF15 - Tpd D2] > Th FF16

The Minimum Library is specified with worst-case multipliers of 0.86 (MAX), 0.78 (TYP) and 0.70 (MIN).

Figure 6-7 Timing Diagrams

In Figure 6-7, FF15 Tpd C->Q (clock to output delay) may be 20% faster than nominal. The total effect of these two variations may be to cause the D input to FF16 to change within the hold time window.

Military Library (Q5000 Series)

The equation for the Military Library maximum value becomes:

1.45 * [0.9 * Tpd D1 + 0.8 * Tpd FF15 - Tpd D2] > Th FF16

The Military Library is specified with worst-case multipliers of 1.45 (MAX), 1.32 (TYP) and 1.19 (MIN).

The computation should be performed using the MAXIMUM (Military or Commercial, as appropriate) worst-case library and then using the MINIMUM library to determine the worst-case external hold time. The ratio of the data and clock path delays will determine which library will produce the larger (most positive number) hold time.

While success can be estimated using Front-Annotation, final calculations must be made after Back-Annotation using the actual metal delays. The layout and/or design must be changed if the appropriate test fails.

Note that tracking may be part of the adjustment factor specifications, in which case the equations would need to be altered to reflect this different specification. Check with the array vendor.

Exercises

  1. Review the design manual for the array you have chosen.

      a. How is tracking specified?
      b. How are external set-up and hold-time specified?
      c. What guidelines are given to minimize the hold-time problems in circuits such as shown in Figure 6-3?

  2. . Compare the array chosen in exercise one with a second array (different series, different vendor).

  3. Write the generic equations for external set-up and hold time for the case where the propagation delays are specified as nominal and the macro set-up and hold times are specified as worst-case.

  4. . Change the register case study to the macros in a library of interest. Write the hold time tracking analysis equations for this circuit. You need to know:
    • how macros are specified - Tpd;
    • how macros are specified - Tsu, Th;
    • if worst-case multipliers or adjustment factors are to be used,
    • what they are; for like and unlike edges,
    • how the vendor specifies tracking;
    • and how macro extrinsic loads (net and fan-out loads) are computed.

Copyright @ 2001, 2002 Donnamaie E. White, White Enterprises
For problems or questions on these pages, contact dew@Donnamaie.com

CST Webinar Series
Verific: SystemVerilog & VHDL Parsers
TrueCircuits: UltraPLL



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy