Bit-Slice Design: Controllers and ALUs

Tying the System Together

Last Edit November 1, 1996; July 20, 2001

The two basic building blocks of a general 16-bit system -- the CCU, including the firmwware interrupt controller, and the RALU -- have been defined in previous chapters. Various other devices are available in the Am2900 family to complete the basic CPU that has been used throughout the text.

Expanded Memory for the Am2903

The Am2903 is designed to be interconnected to the Am29705, via decoders, in order to expand the basic 16x4 scratchpad memory. The Am29705 is a true two-port 16x4 RAM memory which can operate identically to the Am2903's own scratchpad. A logic diagram of the Am29705 is given in Figure 7-1. (The Am29203 uses the Am29707 version.)

Figure 7-1 Am29705 block diagram

By expanding the A, B addresses, scratchpad memory may be added in increments of 16 registers of the rquivalent width of the ALU. An expanded memory interconnect diagram is shown in Figure 7-2 (taken from the original AMD data sheet).

Figure 7-2 Three-Address 64 by 4 memory. A 64-word by 4-bit three-address memory. Data is read from the A address to the YA outputs and from hte B address to the YB outputs while the latch enable is HIGH. When the l;atch enable goes LOW, the YA and YB data are help in the internal latches, and the RAMB address is switched to the C destination address lines. A write pulse will then deposit the input data into the location by the C address.

MUX Requirements

In the course of examining the various arithmetic and shifting algorithms that any given system is to perform, including those few examined in this text, the designer will find it necesary to be able to vary

1. the way that the RALU RAM and Q shifters interconnect
2. the value of carry-in
3. the source of the carry out status bit

The carry in bit could be

1. from a field in the CCU
2. from the ALU Cout (for rotate-by-add or for multiple word precision alforithms)
3. from the ALU Z status line (for the Am2903 multiply for example)

The carry out bit could be sourced from

1. the Cn+4 of the RALU
2. the RAM3 (or S3) output of the RAM shifter.

The shift and rotate interconnections are determined by the particular variations which any given design is to implement. RAM0 (Am2901) or S0 (Am2903) might require connection to Cout, RAM3 (S3), Q3 (extersion register shifter), and ground, VCC or both. Q0 might require a similar flexibility of connection. RAM3 (S3) and Q3 would require complementary connection capability.

In each of these cases, the most obvious solution has been to employ multiplexers with the microinstruction supplying the appropriate selection for any desired connectivity pattern. The Am2904 is designed to replace the carry-in MUX, the carry-out MUX, the RAM0 and RAM3 MUXs, and the Q0 and Q3 MUXs. The Am2904 was developed to reduce the required SSI and MSI support (a.k.a. glue logic) which occurs in typical CPU designs.

Status Register

In the preferred architecture, the one being emphasized throughout this text, a status register is used to hold the status produced by the previous microinstruction (such as the ALU status outputs) for use in determining the next microinstruction address ("branch on result of previous"). The staus outputs of the RALU as well as certain other conditional MUX inputs are considered to be microlevel status inputs.

A sophisticated architecture may also have machine-level status lines, those bits to be tested by the machine-level instructions. A machine-level status register is necessary in this case, and it must be settable at the individual bit level. The Am2904 includes both the microlevel and the macro or machine-level status registers and provides the bit set and certain testing capabilities to further reduce the SSI-MSI system logic support required.