Open side-bar Menu
 Custom Layout Insights
Graham Etchells, Director of Product Marketing at Synopsys
Graham Etchells, Director of Product Marketing at Synopsys
Graham Etchells started in EDA before it was termed EDA. He has held marketing and sales positions at several companies and has been chasing the holy grail of analog/custom layout automation ever since he was a marketing director at Cadence in the mid-1990s. He says past experience indicates we may … More »

Current Solutions for FinFET (Part 3)

 
April 29th, 2016 by Graham Etchells, Director of Product Marketing at Synopsys

What is electromigration (EM) and why is it something we should care about?

Here’s the definition of electromigration from Wikipedia: “Electromigration is the transport of material caused by the gradual movement of the ions in a conductor due to the momentum transfer between conducting electrons and diffusing metal atoms.”

Put simply, when the current density gets too high for a given wire width, you get problems. These problems manifest themselves in two ways, either a void in the metal wire that creates an open circuit or a hillock that creates a short to another wire. Either way your chip fails. Electromigration is made worse by temperature and mechanical stresses.

em

Electromigration in the FinFET process is now a first-order effect and has a huge impact on the Mean Time To Failure (MTTF) of a metal wire. So, as you can imagine, to ensure you have a robust design that will last, great care has to be taken when choosing wire widths for interconnect and power grids.

So what tools do we have to help us in determining the correct wire widths for our interconnect?

There are a variety of tools that will help you check on EM compliance. They range from full-blown ‘signoff’ tools to fast static checkers that can be run while doing the custom physical layout.

For signoff, Synopsys’ CustomSim FastSPICE simulator can calculate current densities in narrow signal nets to determine their susceptibility to EM. Bidirectional current flow is correctly considered, including calculation of the RMS currents required for monitoring Joule heating within the design. CustomSim can also include all of the design’s extracted coupling capacitors, in addition to the grounded capacitors. This provides a high level of precision in determining the current entering or leaving segments of signal net interconnect, enhancing the quality of results. The results are presented as GDSII files which can be overlaid on the design for visualization of the errors.

For the layout engineer, having the ability to run a fast static check interactively during layout is an easy way to catch errors up front. To run EM checks, you need to set up the design with the sheet resistance models for the individual layers. The data for these models comes from the Interconnect Technology File (ITF) that is delivered as part of the interoperable process design kit (iPDK). Once that data is processed, you then set up the current density constraints and the current values on the ports and pins of blocks and devices. The current values can be average, peak and RMS. Now with this information at hand, any net you route to these pins can be checked for EM compliance. To run an EM check you simply select the routed net of interest and invoke the checker. Any EM errors are flagged in the layout with a blinking error marker and an error browser gives detailed information on the type of error and how to fix it.

EM_error_browser

This is a fast and easy way to ensure EM compliance while implementing the layout.

So there we have it. Yes FinFET is complex and there are lots of rules and regulations that you have to abide by to ensure a robust and functioning design. But help is at hand, and, as we have discussed in these last few posts, the layout engineer can call on a good number of tools to help automate the physical layout process.

So the next question is do we need more automation? What do the layout engineers really want?

Look for some ideas in the next post!

Related posts:

Tags: , , , , ,

One Response to “Current Solutions for FinFET (Part 3)”

  1. dhiyar says:

    Thanks for sharing the valuable information here. So i think i got some useful information with this content. Thank you and please keep update like this informative details.

Leave a Reply to dhiyar Cancel reply

Your email address will not be published. Required fields are marked *


*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

CST Webinar Series



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
TechJobsCafe - Technical Jobs and Resumes EDACafe - Electronic Design Automation GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy